CT8030 Main Features - State of the Art ergonomic design and styling for easier handling and use
- Full autorange features
- Large selectable 4¾ or 3¾ digit main display
- 4 digits secondary display
- 42 segments analog bargraph
- DC Voltage measurement up to 1000 Volt
- DC Voltage measurement up to 750 Volt
- AC/DC Current measurement up to 10 A
- Tachometer function with inductive pickup measures from 30 to 20000 rpm
- Dwell measurement in degrees from 0 to 360º or duty cycle from 0 to 100%
- Temperature measurement from -20ºC to 1000ºC or 0º to 1832ºF (selectable ºC or ºF)
- Resistance measurement up to 40 MOhm
- Frequency measurement from 10 to 20 KHz
- Fuel Injection test measures pulse width from 0.05 to 250 mS, or duty cycle from 0 to 100%
- Oxygen Sensor test function
- Alternator test function
- Fault Code Reader
- DTC Decoder
- Diode test
- Continuity Test
- Overload protection
- Soft holster for instrument protection
- Auto power off
CT8030 Applications - Measure engine RPM, ignition dwell angle, and temperature of exhaust manifold, cooling system, air conditioning, heating system, catalytic converter, etc.
- Measure output in sensors like Oxygen (O2), Coolant Temperature, Throttle Position (TPS), Manifold Air, Pressure (MAP), Manifold Air Flow (MAF), etc.
- Check grounds, Voltage drops and continuity across Connectors, Wires, Cables, Relays Contacts, Lamps, Switches, etc.
- Check components like Alternator, Diodes, Relays Coils, Condensers, Ignition Coils, Spark Plug Wires, Magnetic Pick-ups, Motors, Switches, Fuses, etc.
- An essential tool for all around troubleshooting of electrical and electronic circuit and systems.
|
|
Technical Specifications : General Specifications: - 4¾ digits main display
- 4 digits secondary display
- 42 Segments analog bargraph (20 updates/Second)
- Backlight
- Automatic( - ) negative polarity indicator
- Automatic Zeroing
- Automatic over-range indication
- Low battery indicator
- Power Source: One standard 9 Volt alkaline battery
- Physical dimensions (including holster) : 6.30” (H) x 3.22” (W) x 1.89” (D)
- - 160 mm x 82 mm x 48 mm
- Weight: Approximately 12.14 Oz ( 345 g) Including battery
Electrical Specifications: - DC Voltage: 0 to ± 1000V, ±0.3% ± 2 dgts., 10MΩ input impedance
- AC Voltage: 0 to 750V, ±2.5% ± 5 dgts., 10MΩ input impedance,
- 50 to 500 Hz
- DC Current: 0 to ± 10A, ± 0.8 % ± 4 dgts.,
- AC Current: 0 to 10A, ± 0.8 % ± 4 dgts.
- Resistance: 0 to 40 MΩ ± 0.8% ± 5 dgts.,
- Frequency: 0 to 20 KHz, ± 0.01 % ± 2 dgts.
- Tachometer: 30 to 20000 RPM, ± 2 RPM
- Dwell: 0 to 360º, ± 1.2°/ krpm/cyl + 2d
- Fuel Injector (pulse width): 0.05 to 250 mS, ± 0.05 mS +1d
- Oxygen Test: Measures cross count up to 10/Second
- Alternator Test: Measures output voltage ripple, beeps if ripple
- exceeds 0.45V
- Fault code reader: Retrieves blink type fault codes
- DTC Decoder: Retrieves Impulse Code Diagnostic Trouble Codes
- Diode test: 2.4 ± 0.6 mA test current, 3.2 V max. test voltage
- Continuity Test: Audible indicator (Buzzer) with circuit resistance
- is below 100 Ohm
- Temperature: -20º to 1000°C or 0°F to 1832°F (±2% + 1 dgts.)
Accessories Included:
- Battery: 9 Volt alkaline battery included
- Test probes: One red and one black, 1000V/10A
- rated (IEC1010/EN61010 CAT II)
- 35½" long
- Temperature probe: Bead type K thermocouple
- Inductive Pickup for tachometer function
- Hard Storage/Carrying Case: Polypropylene foam padded case
- Soft protective holster
- User Manual
|
No comments:
Post a Comment